Trying to make lm_sensors work correctly with Gigabyte 8KNXP (it87-isa-0290).
---
User then reports:
Modules used:
it87 (parameter: temp_type=0x1c)
i2c_sensor
i2c_isa
i2c_core
The configuration is actually the default conf, with several changes for
temperature and fans. Note that i can't measure any other temp than the
CPU one even from Windows with MBM5. I can't be sure if this happens to
all 8KNXP's or it is just my problem. The Box temperature in MBM5 it has a
permanent reading of 25C.
Configuration (sensors.conf):
chip "it87-*" "it8705-*" "it8712-*"
label in0 "VCore 1"
label in1 "VCore 2"
label in2 "+3.3V"
label in3 "+5V"
label in4 "+12V"
label in5 "-12V"
label in6 "-5V"
label in7 "Stdby"
label in8 "VBat"
set in0_min 1.5 * 0.95
set in0_max 1.5 * 1.05
set in1_min 2.4
set in1_max 2.6
set in2_min 3.3 * 0.95
set in2_max 3.3 * 1.05
set in3_min 5.0 * 0.95
set in3_max 5.0 * 1.05
set in4_min 12 * 0.95
set in4_max 12 * 1.05
set in5_max -12 * 0.95
set in5_min -12 * 1.05
set in6_max -5 * 0.95
set in6_min -5 * 1.05
set in7_min 5 * 0.95
set in7_max 5 * 1.05
ignore vid
compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
compute in4 ((30/10) +1)*@ , @/((30/10) +1)
compute in5 (7.67 * @) - 27.36 , (@ + 27.36) / 7.67
compute in6 (4.33 * @) - 13.64 , (@ + 13.64) / 4.33
compute in7 ((6.8/10)+1)*@ , @/((6.8/10)+1)
ignore temp1
ignore temp2
label temp3 "CPU"
compute temp3 (@ + 20) / 0.9686, (@ * 0.9686) + 65
set temp3_over 45
set temp3_hyst 25
set fan1_div 2
set fan1_min 0
set fan2_div 4
set fan2_min 3000
set fan3_min 3000
And the output of sensors command is:
it87-isa-0290
Adapter: ISA adapter
Algorithm: ISA algorithm
VCore 1: +1.52 V (min = +1.42 V, max = +1.56 V)
VCore 2: +2.62 V (min = +2.40 V, max = +2.60 V) ALARM
+3.3V: +3.34 V (min = +3.13 V, max = +3.45 V)
+5V: +4.27 V (min = +4.72 V, max = +5.24 V) ALARM
+12V: +12.28 V (min = +11.36 V, max = +12.60 V)
-12V: -16.09 V (min = -12.63 V, max = -11.41 V) ALARM
-5V: -8.05 V (min = -5.28 V, max = -4.81 V) ALARM
Stdby: +1.50 V (min = +4.72 V, max = +5.24 V) ALARM
VBat: +4.08 V
fan1: 2884 RPM (min = 0 RPM, div = 2)
fan2: 2220 RPM (min = 2986 RPM, div = 4) ALARM
fan3: 3199 RPM (min = 3000 RPM, div = 2)
CPU: +36C (low = +113C, high = +133C) sensor = invalid
The fan readings look ok (i do have the PSU fan and a box fan connected to
the motherboard). The CPU temp also looks normal (at least it goes up and
down in a logical way and the readings are similar to the ones of MBM5). I
don't understand the "sensor = invalid" line.
The voltage readings as you can see are partially ok. -12 and -5 are
obviously wrong. I did'nt spend more time for voltages, because i don't
actually care much.
