Sensors not found on ML330

[ticket]

Hi, I have a Compaq ML330 with a ServerWorks? CSB6 Southbridge running Debian Etch 2.6.18 and lm-sensors 2.10.1. Have done sensors-detect etc and modprobe'd i2c-piix4 and eeprom, restarted lm-sensors and sensord, but when I run sensors it says no sensors found. Has anyone got any experience with something similar?

[ticket]

Download the latest version (2.10.5) of the lm-sensors package, run sensors-detect and post the full output to the list.

...juerg

[ticket]

I downloaded 2.10.5 and tried to compile it with make user but got a whole lot of errors ............ lib/chips.c:505: error: initializer element is not constant lib/chips.c:505: error: (near initialization for ‘adm1031_features[13].sysctl’) lib/chips.c:507: error: initializer element is not constant lib/chips.c:507: error: (near initialization for ‘adm1031_features[14].sysctl’) lib/chips.c:510: error: ‘ADM1031_SYSCTL_FAN2’ undeclared here (not in a function) lib/chips.c:510: error: initializer element is not constant lib/chips.c:510: error: (near initialization for ‘adm1031_features[15].sysctl’) lib/chips.c:513: error: initializer element is not constant lib/chips.c:513: error: (near initialization for ‘adm1031_features[16].sysctl’) lib/chips.c:515: error: initializer element is not constant ............ About 200 more lines like this then: ............ lib/chips.c:5992: error: initializer element is not constant lib/chips.c:5992: error: (near initialization for ‘f71805f_features[52].sysctl’) lib/chips.c:5994: error: ‘F71805F_SYSCTL_ALARMS_TEMP’ undeclared here (not in a function) lib/chips.c:5994: error: initializer element is not constant lib/chips.c:5994: error: (near initialization for ‘f71805f_features[53].sysctl’) make: *** [lib/chips.ao] Error 1

[ticket]

I'm guessing there is a dependency problem because. The installed version of libc6 is 2.3.6, but the deb package in the Debian testing dist requires libc6 >= 2.6.1, so I assume lm-sensors 2.10.5 will need at least this. I am very reluctant to start messing around upgrading to test/unstable packages as this is a production server. Peter

[ticket]

OK. Managed to upgrade libc6 and install lmsensors/libsensors ver 2.10.4. Output from sensors-detect follows;

# sensors-detect revision 4609 (2007-07-14 09:28:39 -0700)

This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.

We can start with probing for (PCI) I2C or SMBus adapters.
Do you want to probe now? (YES/no): 
Probing for PCI bus adapters...
Use driver `i2c-piix4' for device 0000:00:0f.0: ServerWorks CSB6 South Bridge

We will now try to load each adapter module in turn.
Module `i2c-piix4' already loaded.
If you have undetectable or unsupported adapters, you can have them
scanned by manually loading the modules before running this script.

To continue, we need module `i2c-dev' to be loaded.
Do you want to load `i2c-dev' now? (YES/no): 
Module loaded successfully.

We are now going to do the I2C/SMBus adapter probings. Some chips may
be double detected; we choose the one with the highest confidence
value in that case.
If you found that the adapter hung after probing a certain address,
you can specify that address to remain unprobed.

Next adapter: SMBus PIIX4 adapter at 0700 (i2c-0)
Do you want to scan it? (YES/no/selectively): 
Client found at address 0x51
Handled by driver `eeprom' (already loaded), chip type `eeprom'
    (note: this is probably NOT a sensor chip!)
Client found at address 0x52
Handled by driver `eeprom' (already loaded), chip type `eeprom'
    (note: this is probably NOT a sensor chip!)
Client found at address 0x53
Handled by driver `eeprom' (already loaded), chip type `eeprom'
    (note: this is probably NOT a sensor chip!)

Some chips are also accessible through the ISA I/O ports. We have to
write to arbitrary I/O ports to probe them. This is usually safe though.
Yes, you do have ISA I/O ports even if you do not have any ISA slots!
Do you want to scan the ISA I/O ports? (YES/no): 
Probing for `National Semiconductor LM78' at 0x290...       No
Probing for `National Semiconductor LM78-J' at 0x290...     No
Probing for `National Semiconductor LM79' at 0x290...       No
Probing for `Winbond W83781D' at 0x290...                   No
Probing for `Winbond W83782D' at 0x290...                   No
Probing for `Silicon Integrated Systems SIS5595'...         No
Probing for `VIA VT82C686 Integrated Sensors'...            No
Probing for `VIA VT8231 Integrated Sensors'...              No
Probing for `IPMI BMC KCS' at 0xca0...                      No
Probing for `IPMI BMC SMIC' at 0xca8...                     No

Some Super I/O chips may also contain sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no): 
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor'...                   Yes
Found `Nat. Semi. PC8741x Super IO'                         
    (no hardware monitoring capabilities)
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor'...                   No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Fintek'...                       No
Trying family `ITE'...                                      No

Some CPUs or memory controllers may also contain embedded sensors.
Do you want to scan for them? (YES/no): 
AMD K8 thermal sensors...                                   No
Intel Core family thermal sensor...                         No
Intel AMB FB-DIMM thermal sensor...                         No

Sorry, no sensors were detected.
Either your sensors are not supported, or they are connected to an
I2C or SMBus adapter that is not supported. See doc/FAQ,
doc/lm_sensors-FAQ.html or http://www.lm-sensors.org/wiki/FAQ
(FAQ #4.24.3) for further information.
If you find out what chips are on your board, check
http://www.lm-sensors.org/wiki/Devices for driver status.

[juergh]

Can you run 'lspci -nn -vv' and post the output?

[ticket]

OK here's the output

00:00.0 Host bridge [0600]: Broadcom GCNB-LE Host Bridge [1166:0017] (rev 32)

Control: I/O- Mem- BusMaster?- SpecCycle?- MemWINV- VGASnoop- ParErr?- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr?- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:00.1 Host bridge [0600]: Broadcom GCNB-LE Host Bridge [1166:0017]

Control: I/O- Mem- BusMaster?- SpecCycle?- MemWINV- VGASnoop- ParErr?- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr?- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

00:03.0 VGA compatible controller [0300]: ATI Technologies Inc Rage XL [1002:4752] (rev 27) (prog-if 00 [VGA])

Subsystem: Compaq Computer Corporation Proliant Rage XL [0e11:001e] Control: I/O+ Mem+ BusMaster?+ SpecCycle?- MemWINV- VGASnoop- ParErr?- Stepping+ SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr?- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (2000ns min), Cache Line Size: 64 bytes Region 0: Memory at f7000000 (32-bit, non-prefetchable) [size=16M] Region 1: I/O ports at 2400 [size=256] Region 2: Memory at f6ff0000 (32-bit, non-prefetchable) [size=4K] [virtual] Expansion ROM at 80200000 [disabled] [size=128K] Capabilities: [5c] Power Management version 2

Flags: PMEClk- DSI- D1+ D2+ AuxCurrent?=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:04.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme? BCM5702X Gigabit Ethernet [14e4:16a6] (rev 02)

Subsystem: Compaq Computer Corporation NC7760 Gigabit Server Adapter (PCI-X, 10/100/1000-T) [0e11:00bb] Control: I/O- Mem+ BusMaster?+ SpecCycle?- MemWINV- VGASnoop- ParErr?+ Stepping- SERR+ FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr?- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (16000ns min), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 177 Region 0: Memory at f6fe0000 (64-bit, non-prefetchable) [size=64K] Capabilities: [40] PCI-X non-bridge device

Command: DPERE- ERO- RBC=512 OST=1 Status: Dev=ff:1f.1 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz-

Capabilities: [48] Power Management version 2

Flags: PMEClk- DSI- D1- D2- AuxCurrent?=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=1 PME-

Capabilities: [50] Vital Product Data Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+ Queue=0/3 Enable-

Address: 200201c0d1010280 Data: 4806

00:05.0 System peripheral [0880]: Compaq Computer Corporation Advanced System Management Controller [0e11:a0f0]

Subsystem: Compaq Computer Corporation Unknown device [0e11:b0f3] Control: I/O+ Mem+ BusMaster?- SpecCycle?- MemWINV- VGASnoop- ParErr?+ Stepping- SERR+ FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr?- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 5 Region 0: I/O ports at 1800 [size=256] Region 1: Memory at f6fd0000 (32-bit, non-prefetchable) [size=256]

00:06.0 SCSI storage controller [0100]: Adaptec AIC-7892A U160/m [9005:0080] (rev 02)

Subsystem: Compaq Computer Corporation Compaq 64-Bit/66MHz Wide Ultra3 SCSI Adapter [0e11:e2a0] Control: I/O- Mem+ BusMaster?+ SpecCycle?- MemWINV+ VGASnoop- ParErr?+ Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr?- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (10000ns min, 6250ns max), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 169 BIST result: 00 Region 0: I/O ports at 2800 [disabled] [size=256] Region 1: Memory at f6fc0000 (64-bit, non-prefetchable) [size=4K] [virtual] Expansion ROM at 80220000 [disabled] [size=128K] Capabilities: [dc] Power Management version 2

Flags: PMEClk- DSI- D1- D2- AuxCurrent?=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.0 SCSI storage controller [0100]: LSI Logic / Symbios Logic SAS1064 PCI-X Fusion-MPT SAS [1000:0050] (rev 02)

Subsystem: LSI Logic / Symbios Logic Unknown device [1000:3020] Control: I/O- Mem+ BusMaster?+ SpecCycle?- MemWINV+ VGASnoop- ParErr?+ Stepping- SERR+ FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr?- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 72 (16000ns min, 2500ns max), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 193 Region 0: I/O ports at 2c00 [disabled] [size=256] Region 1: Memory at f6fb0000 (64-bit, non-prefetchable) [size=16K] Region 3: Memory at f6fa0000 (64-bit, non-prefetchable) [size=64K] [virtual] Expansion ROM at 80000000 [disabled] [size=2M] Capabilities: [50] Power Management version 2

Flags: PMEClk- DSI- D1+ D2+ AuxCurrent?=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-

Capabilities: [98] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-

Address: 0000000000000000 Data: 0000

Capabilities: [68] PCI-X non-bridge device

Command: DPERE- ERO- RBC=512 OST=16 Status: Dev=ff:1f.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=16 DMCRS=128 RSCEM- 266MHz- 533MHz-

Capabilities: [b0] MSI-X: Enable- Mask- TabSize?=1

Vector table: BAR=1 offset=00002000 PBA: BAR=1 offset=00003000

00:08.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6105 [Rhine-III] [1106:3106] (rev 86)

Subsystem: D-Link System Inc DFE-530TX rev C [1186:1403] Control: I/O+ Mem+ BusMaster?+ SpecCycle?- MemWINV+ VGASnoop- ParErr?+ Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr?- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (750ns min, 2000ns max), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 185 Region 0: I/O ports at 3000 [size=256] Region 1: Memory at f6f90000 (32-bit, non-prefetchable) [size=256] [virtual] Expansion ROM at 80240000 [disabled] [size=64K] Capabilities: [40] Power Management version 2

Flags: PMEClk- DSI- D1+ D2+ AuxCurrent?=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:09.0 Communication controller [0780]: Agere Systems LT WinModem? [11c1:044c] (rev 02)

Subsystem: Agere Systems LT WinModem? [11c1:044c] Control: I/O+ Mem+ BusMaster?+ SpecCycle?- MemWINV- VGASnoop- ParErr?+ Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr?- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (63000ns min, 3500ns max) Interrupt: pin A routed to IRQ 3 Region 0: Memory at f6f80000 (32-bit, non-prefetchable) [size=256] Region 1: I/O ports at 3400 [size=8] Region 2: I/O ports at 3800 [size=256] Capabilities: [f8] Power Management version 2

Flags: PMEClk- DSI+ D1- D2+ AuxCurrent?=0mA PME(D0-,D1-,D2+,D3hot+,D3cold-) Status: D0 PME-Enable+ DSel=0 DScale=0 PME-

00:0e.0 IDE interface [0101]: Broadcom CSB6 IDE Controller [1166:0217] (rev a0) (prog-if 82 [Master PriP])

Subsystem: Broadcom Unknown device [1166:0213] Control: I/O+ Mem- BusMaster?+ SpecCycle?- MemWINV- VGASnoop- ParErr?- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr?- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Interrupt: pin ? routed to IRQ 14 Region 0: I/O ports at <ignored> Region 1: I/O ports at <ignored> Region 2: I/O ports at <ignored> Region 3: I/O ports at <ignored> Region 4: I/O ports at 2000 [size=16] Capabilities: [b0] Power Management version 2

Flags: PMEClk- DSI- D1- D2- AuxCurrent?=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0f.0 ISA bridge [0601]: Broadcom CSB6 South Bridge [1166:0203] (rev a0)

Subsystem: Broadcom Unknown device [1166:0201] Control: I/O+ Mem+ BusMaster?+ SpecCycle?- MemWINV- VGASnoop- ParErr?+ Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr?- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 32

00:0f.2 USB Controller [0c03]: Broadcom CSB6 OHCI USB Controller [1166:0221] (rev 05) (prog-if 10 [OHCI])

Subsystem: Broadcom Unknown device [1166:0220] Control: I/O+ Mem+ BusMaster?+ SpecCycle?- MemWINV+ VGASnoop- ParErr?+ Stepping- SERR+ FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr?- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (20000ns max) Interrupt: pin A routed to IRQ 10 Region 0: Memory at f6f70000 (32-bit, non-prefetchable) [size=4K]

00:0f.3 Host bridge [0600]: Broadcom GCLE-2 Host Bridge [1166:0227]

Subsystem: Broadcom Unknown device [1166:0230] Control: I/O- Mem- BusMaster?+ SpecCycle?- MemWINV- VGASnoop- ParErr?- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr?- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0

[juergh]

This machine doesn't seem to contain any sensors we know about.